|Categories||Air Compressor Manuals, Ingersoll Rand Air Compressor Manuals|
|Tags||Ingersoll Rand SS3, Ingersoll Rand SS5|
|Document File Type|
ingersoll IMPORTANTDEFINITIONS /k_ WARNING CAUTION WILL cause DEATH, SEVERE INJURY or substantial property damage CAN cause DEATH, SEVERE INJURY or substantiaI property damage, WILL or CAN cause MINOR INJURY or property damage. SAFETY PRECAUTIONS Owner’s Manual Installation, Operation and Maintenance Instructions for Models SS3 and SS5 Stationary Air Compressors AND FOLLOW THESE INSTRUCTIONS. RETAIN FOR REFERENCE. INFORMATION! READ Your air compressor unit suitable for operating air too_s, caulking is guns, grease guns, sandblasters, etc Depending on your application, the following accessories may be required: @ An air pressure regulator toot or accessory · to adjust the alr pressure enlering the An air line fitter for removal of moisiure and oil vapor in compressed air An in-line lubricator to prolong lhe life of air tools.
GENERAL ,_ _ · iNTAKE AIR, Can contain carbon monoxide or other contaminants. Will cause serious injury or death ingersoll-Rand air compressors are not designed, intended or approved for breathing air Compressed air should not be used for breathing air applications unless treated in accordance with all applicable codes and regulaUons,, HAZARDOUS VOLTAGE Can cause serious injury or death. Disconnect power and bteed pressure from tank before servicing Lockout/Tagout machine. Compressor must be connected to properly grounded circuit See grounding instructions in manuat, Do not operate compressor tn wet conditions,, Store indoors MOVING PARTS, Can cause serious injury Do not operate with guards removed. Machine may start automatically Disconnect power before servicing_ Lockout/Tagout machine,, HOT SURFACES, Can cause serious touch Allow to cool before servicing hot compressor or tubing injury, r DO not Do not touch ql, Separate air transformers which combine the !’unctions of air regulation andlor moisture and dirt removal Cenlact your nearest authorized dealer or cal! 1-800-AIR-SERV for more information on air toots and accesser}as for your application WARNING Ensure adequate lifting equipment moving your unit to the inslaIlatton NOTE: is available site for unloading and Lifting equipment must be property rated for the weight of the unit. Lift the unit by the shipping skid only,, Use straps to prevent tipping Lk CAUTION Do not work on or walk under the compressor it is suspended, while – . HIGH PRESSURE AIR. Bypassing_ modifying or removing safety/relief valves can cause serious injury or death, Do not bypass, modify or remove safety/relief valves Do not direct air stream at body. Rusted tanks can cause explosion and severe injury or death Drain tank daily or after each use. Drain valve located at bottom of tank. z_ CAUTION RISK OF BURSTING. Use only suitable air handling parts acceptable for pressure of not less than the maximum allowable working pressure of the machine. Be[ore signing the delivery receipl, inspecl for damage and missing parts If damage or missing parts are apparenL make the appropriate notation on the delivery receipt, then sign the receipt. Immediately contact the carrier for an inspection. All material must be held in the receiving location for the carrier’s inspection Deiivery receipts that have been signed without a notation of damage or missing parts are considered to be delivered “clear ” Subsequent claims are then considered to be concealed damage claims SeUle damage claims directly with the transportation company Lf you discover damage after receiving the unit (concealed damage), the carrier must be notified within 15 days of receipt and an inspection must be requested by telephone with confirmation in writing On concealed damage claims, the burden of establishing that the unit was damaged in transit reverts back to the claimant Read lhe unit specification labei to verify it is the mode! ordered. and read the meier nameplate to verify il is compatibJe with your e_ectrical conditions Make sure electrical enclosures and componenls are appropriate for your applicafion IngersolL-Rand Printed in U S A Company Form SCD-B77A March 2002 _ WARNING SELECTING A LOCATION GENERAL° Select a clean, dry, welt-lighted indoor area with plenty of space far proper cooling air flow and accessibility. Locate the unit at least 12 inches (30 cm) from wails, and make sure the main power supply is clearly identified and accessible TEMPERATURE Ideal operating temperatures are between 32 “F and 100°F (0°C and 37.B_C) If temperatures consistently drop below 32°F (0 “C), locale the unit inside a heated building
Wikipedia’s page for Ingersoll-Rand